BestofBest11

Mathew Phillips' hand made grips

"I just finished some grips and forearm for my 1377. It is my first time out the gate. I couldn't handle the plastic any longer. I left the large flat under the thumb rest to laser etch later. I also need another coat of finish on the forearm just could wait any longer before taking pics.

Latest Zombie Hunter Mod

Latest mod from ZombieHunter.

After opening up the intake side of the Max-flo valve head (seems a bit redundant, don't you think?) to 19/64ths, trimming and reshaping the delrin poppet stem, and removing a few links off of a uselessly long valve spring, which was interfering with hammer travel.........I ended up with a 39-shot average of 748fps!

Max output of 782 for 19.67 fpe shooting CPs, while not quite at my target of 20 fpe, I'm much happier with the results. After the last shot (#39) was fired, the remaining air left in the tank empties out, but that shot still made 653fps. There's no mistaking when you have to refill.

Randy's Condor

My Condor is relatively stock as I am just doing shooting platform mods first then working the internals. It has a 4-12 power illuminated scope, Airforce bipod, steel muzzle brake, flip down fore grip, Morgan butt-plate, Philips Pellet Holder, 90 L flashlight, green daylight laser, tactical sling, AR-15 DPMS tactical pistol grip, and a new steel trigger guard. Using heavy 29 grain .22 pellets on power setting 9 with a 2600 psi fill this air rifle is quite of taking gophers out to 100 yards and blowing right thru an spruce 2X4, accuracy with the choked Lothar barrel is also incredible! I average 40 very strong shots per 430cc butt-stock fill. On the books for future mods is the valve “O” ring mod, heavy hammer, and maybe a .25 caliber upgrade.
Oh also with 28 grain pellets I am getting 65 lbs of energy.

Robert's Custom Drozd

It has a 1200 RPM full auto mod board. It also has the new JimC Mix-n-Match barrel kit set up in the tactical rifle configuration. A JimC bulk air adapter. A RIT dye job and a BSA red
dot scope. The pot has been tweaked and the solenoid has been adjusted for max performance. I'm getting over 700 fps with BB's. All the mods were done myself. I'm currently working on a 2250B project. It also has a Picatinny rail under the forearm with
a airsoft tactical handle and a BSA laser.

Very nice gun case from Mike Robinson.

Here is the inside of the case I made. It's a wood case covered in leather like vinyl with a foam padded interior that is covered in green felt material that is like pool table cloth.

Chevell's Newest 1322 Creation...what a beauty!!

Front and back view	12 pumps	15 pumps	18 pumps
These results easily surpass the best numbers of my modded steroid streak despite the fact that my gun has a much smaller pump volume displacement and much smaller valve. Kinda gives new meaning to the word efficiency. It's also twice as easy to pump as my steroid gun even with no extra leverage and a metal handle! It will also be much more accurate because of the stiffness of the perfectly honed 304 stainless pump tube which is locked to my Crosman barrel with brass barrel bands. This gun has all the mods I used on my 1322 carbine and a few new ones as well. It's also very quiet, even on the higher pump levels. This is the gun as tested, the pistol grips are just for testing. It will have a top of the line full size walnut stock and a Leapers 8-32 AO 56mm scope. Crosman Premiers, 22 cal. 14.3 grain.

Tim Miller's 3240

It shoots a tad over 600 fps with the 45 grain round-balls. The gun is not finished, but I really like it already!

Tim Miller

Stylish Handmade 1377 Stock from Bruce

Another nice creation from Bruce