Best of the Best

Page 6

One of the nicest 1377s I have ever seen. Nice work CharlesC.

Brass1377.jpg (127405 bytes) SightonBrass1377.jpg (121514 bytes)
It started out as a rifle, went to a scoped pistol config and now it's an iron sighted pistol. Of my three 1377's this is the one I like most for plinking. 
I machined the receiver/breech and barrel weight/sight holder out of some scrap brass hex bar stock that was laying around my machine shop. 
Bolt dimensions are more like a 397 than a typical 1377. The bolt groove next to the breech is pellet diameter and the rear section is larger diameter to give more meat to thread the bolt handle into. 
I used an Iron Sight Gun Works rear sight that I grooved to snap down over the scope grooves. It's held down with the 4-48 screws that came with the sight. I made the front blade .150" wide to give me the 1-2-1 sight picture I like when the pistol it held at arms length.
The barrel is 1/2 of a 1760 rifle barrel. 
It's a fun pistol to shoot, is very accurate and isn't fussy about the kind of pellets it likes.
Innards are mostly stock including old style brass cup air chamber outlet valve. Of course I've fiddled around with the trigger a bit. 

John Richardson, AKA Johnny Bravo's most excellent Crosman 600.

CustomShineyCR600005.jpg (179999 bytes) CustomShineyCR600004.jpg (206177 bytes) CustomShineyCR600006.jpg (212524 bytes)
CustomShineyCR600007.jpg (232849 bytes) CustomShineyCR600013.jpg (179425 bytes) CustomShineyCR600008.jpg (183556 bytes)
From the Crosman Forum 8-16-06

Pistols002.jpg (239379 bytes)

Old Look 

This has taken almost 1 year in the making but she is 95% complete. Lots of folks to thank too. The first pic is what she USED to look like before I put her in Oakland Raider colors for that BA look.  Definite Eye Candy for the 600 lover.

 

1155557198.jpg (48178 bytes) 1155559381.jpg (62983 bytes)
David Enoch's Custom case and LD

 

IMG_0007.JPG (854715 bytes) IMG_0008.JPG (1381187 bytes) IMG_0004.JPG (431654 bytes) IMG_0005.JPG (1102181 bytes)
Mark's impressive 1377 with a freaking fantastic new design from Steve Corcoran.

 

Hybrid22 Pump.JPG (110587 bytes)
From Mike Marsh: Hybrid  22 cal, straight thru valve with hollow bolt, 12" shrouded barrel, CO2 or HPA. Magpie dot sight, 650fps co2, 750fps HPA. Built on paintball gun frame.

 

1322B.jpg (123815 bytes)
Pat J's tricked out MA1322 by Roy at Mountain Air

 

Shroud 12 inch barrel.jpg (142485 bytes) Shroud 12 inch barrel 2.jpg (203037 bytes)
Another great looking 2240 from Pat J

 

Pumpers019r.jpg (78809 bytes) Pumpers025r.jpg (64053 bytes) Pumpers027r.jpg (80389 bytes)
Pumpers032r.jpg (98891 bytes) Pumpers037r.jpg (102711 bytes) Pumpers040r.jpg (116317 bytes)
Robert Copple's impressive airgun collection. 

 

gallery1.jpg (24656 bytes)  gallery3.jpg (34891 bytes)  gallery4.jpg (29299 bytes)  gallery5.jpg (51747 bytes)  gallery6.jpg (53322 bytes)  gallery7.jpg (16317 bytes)

The finest shooting gallery I have ever seen.

My2289.jpg (44467 bytes) My2289barrel002.jpg (48314 bytes) My2289barrel003.jpg (59048 bytes)
"I made an aluminum breech and brake and put on some good quality sights. Also a brass pump shaft. What a difference!!!"

George Ewen's 2289 with homemade breech.

 

My 1322 002.jpg (53384 bytes) My 1322 004.jpg (63026 bytes) My 1322 005.jpg (59659 bytes)
George Ewen's Custom 1377

Would you look at that pump handle? I mean...Look at it!!!!

 

MVC-864F.jpg (65095 bytes) MVC-861F.jpg (60665 bytes)
Ron's new grips from Rick

Click on any picture to enlarge

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

HOME